Note: if you are using a photocopy, put the blue filter behind the grasp and insert them collectively.put a clean card on the foam mattress (to maintain your artwork from sticking to it), and put your unique artwork on prime of that. i drew this image using the gocco marker (included in gocco set). In case you have almost any questions concerning where and also the way to use screen printing mesh blog, you’ll be able to email us with our webpage. position your artwork where you need it.

shut the lid can examine visually that your artwork is where you want it to be.

however 2 bulbs into the print hood (yellow part) can insert the hood into the print gocco physique. here is the primary aspect.

here’s the second aspect.

at this level the order is top to backside: yellow flash hood; clear plastic window in the gocco; blue filter; mesh master; original artwork; clean paper; foam bed.

when it is pressed down, the hood makes a complete circuit that may cause the bulbs to flash.

put each your hands on the entrance of the gocco (the picture just has certainly one of my arms, as a result of the opposite one is holding the digital camera, but you possibly can see the place your palms should go).

push down (you will see the the flash and listen to a crackling noise) and hold for 3-5 seconds.

open your gocco. your artwork will most like be caught to the grasp. take away the grasp (and blue filter, should you used it to create a grasp from a photocopy).

once you take away the yellow print hood, be careful not to touch the bulbs until they cool.

this is the grasp with my design exposed on it.

with the master out of the gocco, display screen side down and sitting on a piece of scrap paper, raise the clear plastic up and squeeze ink out of the tube on to the area the place your design is. if you haven’t but, peal your authentic off the master. (leaving it on till now can be useful to see where exactly you want to ink).

exchange the clear plastic layer and and put the inked master again into the gocco the same means and position as earlier than. if you have not eliminated the flash hood, screen printing mesh blog do it now.

now the order is: clear plastic window within the gocco, clear plastic sheet over the ink, ink, mesh master.

put whatever you need to print on on the sticky grey foam mattress. now it is going to be useful that it is sticky because it holds your prints in place.

close the gocco to make a print. *repeat.*

that is my print on fabric.

these are all of the things i printed on. and printing on felt was awesome.

this method above can be used to print on paper or fabric, though to print on fabric, it’s worthwhile to used particular gocco fabric ink. (EDIT: industrial filter mesh you may print on fabric with the identical kind of display and similar process that you should use to print on paper-just use ‘gocco stamp ink for fabric’).

one other solution to print on fabric is as a substitute of using the hi mesh grasp (which can be used for both paper or fabric printing), use the gocco display masters especially for display printing on fabric. with these, you cannot use the gocco to print, quite you employ the gocco to make the display screen, and then print like typical screenprinting, using gocco screenprinting ink, which is available in jars and isn’t the same because the ‘stamp ink for fabric’ that is available in tubes.

this can be a screened print i did utilizing the gocco display and screen inks. it was from a photocopy of a conventional japanese display, so the meshy background is from the original picture.

cleanup:

the screens could be re-used many many many times. you’ll be able to retailer them in a ziploc bag within the fridge and take them out when you’re ready to make use of them next time. this way, you don’t even have to scrub off the inks.

the fabric inks are water based mostly. i recommend taping the cardboard edges of your display earlier than you begin, that approach they will not fall apart or warp after cleanup with water.

you need to use the gocco cleaner with the paper inks, but they will even wash off if held underneath working water (this is where the tape comes it). you can also wipe with a sponge or paper towels. remember that it is necessary to wash the print area only, and it the screen is stained in other locations it won’t affect your future prints.

present scenario:several years ago gocco’ s mother or father firm riso announced that gocco’s would not be exported to the united states. this precipitated a bit of a frenzy and result in creation of the save gocco marketing campaign. EDIT: after a number of years of restricted supplies, evidently gocco will certainly be ceasing production in the next yr or so.